Library

The installation location of the cooling tower has the following requirements: Ventilation requirements The cooling tower should be installed in a place with sufficient air inlet volume to ensure sufficient air flow into the tower. The distance between the air inlet side and the building should be greater than 1000mm to avoid poor ventilation affecting the heat dissipation effect. An open area should be selected around the cooling tower as much as possible to ensure that there is enough space for air circulation to prevent hot air from backflowing. Location Selection The cooling tower should be positioned to take into account the backflow of cooling water. For open cooling water systems, cooling towers may need to be placed at a high level to allow for natural return. Cooling towers should not be installed in locations with poor ventilation and wet air backflow, as this will reduce the cooling capacity of the cooling tower. Cooling towers are typically installed on the

The installation process of spray exhaust cooling tower needs to pay attention to the following: 1. Site selection and site preparation The cooling tower should be installed in a place with good ventilation conditions to ensure air circulation and avoid poor ventilation affecting the heat dissipation effect. The installation site should be kept away from places with dense dust and dirt, acidic gases, and places with a lot of soot and dust to prevent clogging of the film. The cooling tower should be installed in an open place that will not amplify the noise due to echoes, and ensure that there is a certain distance from the building, 2 meters for single towers and 2.5 meters for combined towers. The site should be level, barrier-free, and cleared for construction. Second, the foundation construction According to the instructions, it is recommended to pre-build the cement foundation, and ensure that the foundation level cannot be tilted, otherwise it will affect the water

Spray exhaust cooling towers are suitable for the following locations: Industrial cooling Especially in scenarios where the operating temperature of machines or equipment needs to be reduced, such as the cooling of high-temperature furnaces, furnaces, and other equipment. Spray cooling towers are able to effectively remove the heat generated by the equipment through the evaporation of water, thus maintaining the normal operating temperature of the equipment. Industries such as power, chemicals, machinery, etc. Many production processes in these industries generate a lot of heat and require effective cooling systems to ensure production efficiency and equipment safety. Spray exhaust cooling towers are ideal for these industries due to their efficient cooling capacity and relatively low operating costs. Noise-sensitive areas such as hotels, hospitals, schools, and residential areas. Due to the relatively low noise generated by the spray exhaust cooling tower during operation, especially the noise reduction measures are also adopted in some new design towers, it is suitable for use in

The working principle of the condenser can be clearly divided into the following steps: Cooling Phase: The gas or vapor flows through a ductwork system inside the condenser. These gases or vapors come into contact with a cooling medium, such as water or air, to initiate heat exchange. In this stage, the cooling medium absorbs heat, causing the temperature of the gas or vapor to gradually drop. Condensation Phase: When the temperature of the gas or vapor is reduced to a certain level, its saturation temperature is reached, and it begins to condense into a liquid. This is because the cooling medium absorbs enough heat that the gas or vapor cannot continue to remain in a gaseous state. The latent heat released during the condensation process further increases the thermal efficiency of the condenser. Heat Transfer Stage: Heat is transferred from gas or vapor to the cooling medium, which is achieved by means of both heat convection and heat conduction.

There are distinct differences between air condensers and water condensers in several ways, and here is a detailed analysis of their differences: Cooling medium: Air condenser: uses air as the cooling medium to remove the heat of condensation of refrigerant vapors through the natural convection or forced flow of air. Water condenser: water is used as the cooling medium, and the condensation heat is taken away by the heating of the water. Cooling water is generally recycled, but the system needs to be equipped with a cooling tower or a cooling pool. How it works: Air condenser: The refrigerant vapor enters the snake tube from the upper header, and the outer ribs of the tube are used to strengthen the heat transfer on the air side and compensate for the defect that the heat transfer coefficient of the air surface is too low. It does not require a fan, has no noise, and is mostly used in small refrigeration units.

As an important heat exchange equipment, the common application scenarios of water condenser can be summarized as follows: Refrigeration: In refrigeration systems, water condensers are often used to change the refrigerant from a gaseous to a liquid state to ensure that the refrigeration system can function properly. It uses cooling water to condense high-temperature and high-pressure steam into a liquid, completing a critical step in the refrigeration cycle. Air conditioning field: The air conditioning system will generate a lot of heat during the cooling or heating process, and if the heat exchange treatment is not carried out, the normal operation of the system will be affected. The water condenser plays a key role in this time, dissipating the heat generated from the system and ensuring the continuous and stable operation of the air conditioning system. Industries: Water condensers are widely used in industrial fields, such as petrochemical, metallurgy, electric power, pharmaceutical and other industries. In these industries, water condensers are

Water condenser is an important heat exchanger, and its main role is reflected in the following aspects: Temperature control in industrial processes: Water condensers are often used in the industrial field to reduce the temperature of heated industrial fluids through the cooling of the fluid flowing through the outer surface through their heat exchange function, so that they can meet the needs of actual production or operation. Condensation of high-temperature and high-pressure gases: In the refrigeration system, the water condenser is a device for heat exchange of high-temperature and high-pressure gases discharged from the new refrigeration compressor, which transfers the heat of the refrigerant to the cooling medium (such as water), so that the refrigerant is condensed into a medium-temperature and high-pressure liquid. Exothermic and heat dissipation Water condensers play a key role in heat dissipation and heat dissipation during the refrigeration process. It is able to convert gas or vapor into liquid, and quickly transfer the heat in the

An ejector in the petrochemical industry is a fluid machine with a wide range of applications. Here’s a detailed explanation of injectors in the petrochemical industry: Definition The ejector uses the jet action of the working fluid to transfer energy and mass, which has the role of transportation and mixing. Type According to the different working medium and the injection medium, the injector can be divided into various types, such as gas-liquid injector, gas-solid injector, liquid-liquid injector, etc. Compose The injector is mainly composed of four parts, including a gas nozzle, a suction chamber, a mixing chamber, and a diffusion chamber. How it works Steam at a certain pressure is shot at supersonic velocity through a Laval nozzle, which is converted from pressure energy to velocity energy. At the outlet of the nozzle, the working steam is mixed with the extracted air stream in the mixing chamber due to the low pressure formed by the induction action of the high-velocity

In the chemical industry, the use of ejectors is quite extensive, and their type and application depend on the specific process needs and working medium. Here are some of the types of ejectors that may be used in the chemical industry and their brief descriptions: Water vapor ejector Working medium: water vapor Features: It can directly exhaust the atmosphere, fast starting, small footprint, wide working pressure range, large pumping capacity, and can extract dust, corrosive and flammable and explosive gases. Application: It is more economical to use surplus or waste steam, but the disadvantage is high civil investment and high cooling water consumption. Air Injectors Working medium: compressed air or steam Features: The jet action of compressed air is used to transfer energy and mass, and it has the effect of transportation and mixing. Application: Widely used in processes that require air or steam as a power source. Liquid Injectors Working medium: all kinds of liquids, such as water, oil,